Amlogic USB driver for Windows 10 (64-bit) is a critical component that enables your computer to communicate with devices powered by Amlogic chipsets, such as Android TV boxes and tablets. Its most helpful feature is facilitating the "Burning" or flashing process through the Amlogic USB Burning Tool
, which is used to manually update or restore firmware when standard over-the-air (OTA) updates are unavailable. CoreELEC Wiki Key Features and Capabilities Firmware Recovery & Repair
: It allows you to repair a corrupted bootloader or replace damaged firmware that prevents the device from starting normally. Support for Large Image Files
: The associated tool supports burning image files larger than 1GB, making it suitable for modern, feature-rich Android firmware. Device Recognition (WorldCup Device)
: Once installed, the driver allows Windows to recognize the connected device in special modes (often appearing as "WorldCup Device" or "android_winusb" in Device Manager), which is necessary for the PC to send data to the device's internal storage. Direct eMMC Burning
: It supports burning directly to a "blank board" (empty board), which is essential during production or for advanced hardware recovery. Installation Highlights for Windows 10 64-bit Automatic Installation : In many versions of the Amlogic USB Burning Tool
, drivers are installed automatically during the software setup process. Manual Override
: If the device shows a yellow exclamation mark in Device Manager, you can manually point Windows to the
sub-directory within the tool's installation folder (typically C:\Amlogic\Aml_Burn_Tool\V3\Driver ) to complete the setup. Antivirus Compatibility : It is highly recommended to disable antivirus software
during installation to prevent critical library files from being mistakenly blocked. MINIX Forum Usage Tips Required Hardware : You typically need a USB male-to-male cable
to connect your Amlogic device to the computer for flashing. Port Selection : It is often advised to use USB 2.0 ports
instead of USB 3.0 to avoid connection stability issues during the burning process. MINIX Forum , or do you need help troubleshooting a device that isn't being recognized?
Amlogic Burning Tool Guide (0.4) | PDF | Device Driver | Usb - Scribd 2 Nov 2020 —
To install Amlogic USB drivers on Windows 10 (64-bit), the most reliable method is to install the Amlogic USB Burning Tool , which includes the necessary drivers in its installation package. Step 1: Download the Amlogic USB Burning Tool
While there is no single official consumer website, reputable community sources like the MINIX Forum CoreELEC Wiki provide verified versions of the tool. Version 2.x
: Generally more stable for older Amlogic chips (S905, S912). Version 3.x
: Required for newer Android 11+ devices or chips like the S928X. Step 2: Installation Process Extract the Files : Right-click the downloaded zip file and select "Extract Here" Run the Installer : Double-click the USB_Burning_Tool.exe Install Drivers
: During the setup, a prompt will appear asking to install required device drivers (often labeled "World Cup Device"). Select to permit this. : Once completed, click . The drivers are now registered on your system. Step 3: Verifying the Connection To check if the drivers are working: Amlogic USB Burning Tool Recovery Guide: Revised Tutorial
Here’s a short, informative story based on that search query. amlogic usb driver windows 10 64 bit
Title: The Bootloop Fix
Lena stared at her bricked TV box. The orange light glowed, but the screen was black. The Android logo was frozen mid-spin. She’d tried to flash a new firmware, but the PC didn’t see the device. Just a silent “USB device not recognized.”
The search history read: “amlogic usb driver windows 10 64 bit.”
It was 11 PM. Her living room looked like a tech repair shop: cables everywhere, a screwdriver, tweezers, and a paperclip for the reset button. The box was an Amlogic S905X3—cheap, powerful, and now, a paperweight.
She clicked the first result—a forum post from 2019. The user “balbes150” had a link. "World-cup drivers," they called them. Not official. But nothing about Amlogic ever was.
Step one: Disable driver signature enforcement on Windows 10. She rebooted, pressed F7, and watched the command lines scroll by like incantations.
Step two: Install the driver manually. Not through the installer—that never worked. She opened Device Manager. The bricked box showed up as an “Unknown USB Device (Device Descriptor Request Failed).”
Right-click. Update driver. Browse my computer. Let me pick from a list. Have disk.
She browsed to the extracted folder: Amlogic_USB_Burning_Tool_v2.2.0/driver.
Clicked the .inf file. A warning popped up: “This driver isn’t signed.” She ignored it. Installed anyway.
The device blinked. Refreshed Device Manager. And there it was: “WorldCup Device” under Universal Serial Bus devices.
Her heart jumped. That was the magic name. Amlogic’s hidden boot mode.
She opened USB Burning Tool v2.2.0. Loaded the correct .img firmware file for her box (found after two hours of sifting through Russian forums). Clicked Start. Then, with a paperclip, she pressed the reset button inside the AV port and plugged in the USB cable.
A green progress bar appeared.
Download DDR. Initialize DDR. Download UBOOT.
1%. 4%. 17%.
At 53%, the tool beeped red. Error: [0x30405003]USB control setup error.
She almost cried. But then she remembered—older USB 2.0 port, not the blue USB 3.0. She swapped cables, restarted the process. Amlogic USB driver for Windows 10 (64-bit) is
This time: 100%. Success.
The TV box rebooted. The logo appeared. Then the setup wizard.
She leaned back, exhaled. The Amlogic USB driver for Windows 10 64-bit wasn’t just a driver. It was a key to a locked room. And tonight, she’d picked the lock.
Guide: Installing Amlogic USB Driver on Windows 10 64-bit
Introduction
Amlogic is a popular System-on-Chip (SoC) manufacturer for Android devices, smart TVs, and other embedded systems. If you're a developer or user who needs to connect an Amlogic-based device to your Windows 10 64-bit system via USB, you'll need to install the Amlogic USB driver. This guide will walk you through the process of installing the Amlogic USB driver on Windows 10 64-bit.
Prerequisites
Step 1: Enable Developer Options on Your Amlogic Device
Step 2: Enable USB Debugging on Your Amlogic Device
Step 3: Download and Install the Amlogic USB Driver
C:\Amlogic_Driver).Step 4: Connect Your Amlogic Device to Your Windows 10 System
Step 5: Install the Amlogic USB Driver on Windows 10
C:\Amlogic_Driver).android_usb.inf file (or a similar file with a .inf extension).Step 6: Verify the Amlogic USB Driver Installation
Troubleshooting
Conclusion
Installing the Amlogic USB driver on Windows 10 (64-bit) is a critical step for anyone looking to unbrick, upgrade, or flash custom firmware onto Android TV boxes using the Amlogic SoC. Without this driver, your PC will not communicate with your device in "Burning Mode." 1. Download the Necessary Tools
The Amlogic USB driver is rarely a standalone download; it is typically bundled with the Amlogic USB Burning Tool.
Amlogic USB Burning Tool (v3.2.0 or v2.1.7.0): These versions are widely used and include the necessary driver installers in their installation directories. Title: The Bootloop Fix Lena stared at her
Driver Files: Once you extract or install the tool, the drivers are often located in a subfolder named Driver within the installation path (e.g., C:\Amlogic\Aml_Burn_Tool\Driver). 2. Automatic Installation Method
The easiest way to install the drivers is during the setup of the USB Burning Tool itself.
Run the USB_Burning_Tool.exe (or setup file) as an Administrator.
Follow the prompts. Towards the end of the installation, a separate window will pop up specifically for Device Driver Installation.
Click Next and then Finish to allow Windows to register the Amlogic drivers. 3. Manual Installation (For Windows 10 64-bit)
If the tool doesn't recognize your device, you may need to force the driver installation manually via the Device Manager. Amlogic USB Burning Tool - 4PDA
Download the latest USB_Burning_Tool.zip (seek version 2.2.4 or newer for best Windows 10 compatibility). Extract it to a folder like C:\Amlogic\USB_Burning_Tool.
Inside the extracted folder, you should find:
Cause: Windows 10’s driver signature enforcement blocked the driver.
Fix: Re-disable enforcement using the Shift + Restart method. Also, check your USB cable—many cheap cables are charge-only. Use a short (under 3 feet) data-sync cable.
Since the Amlogic driver is not officially Microsoft-signed, you must temporarily disable driver signature enforcement. Here are two methods:
Method A (Temporary – Recommended for a single session):
Method B (Permanent via Group Policy – Advanced Users only):
Now that the driver is active:
If you own an Android TV box, a development board (like the Odroid-N2), or a generic streaming stick powered by an Amlogic chipset (S905, S912, S922X, etc.), you have probably encountered the need to flash firmware, unbrick a device, or perform a low-level format. To communicate with your PC, you need one critical piece of software: the Amlogic USB Driver for Windows 10 (64-bit).
Without this driver, your computer will not recognize the device when it is in "Burn Mode" or "Mask ROM Mode." Windows might show an error like “USB device not recognized” or label it as an “Unknown Device.” This guide will walk you through everything you need—from downloading safe drivers to troubleshooting installation failures on modern 64-bit versions of Windows 10 and Windows 11.
Do not run the USB Burning Tool yet. First, install the driver:
Cause: The driver is loading, but the device is undervolted.
Fix: You must provide external power to the Amlogic box while flashing. Plug in the power adapter after you connect the USB cable and hear the connection sound.