Digi Edgeport 1 Driver Windows 10 64 Bit -
After the installation and system reboot, you need to confirm Windows recognizes the device as a COM port.
To prevent Windows from turning off the device to save power:
The Digi Edgeport/1 is highly regarded as a professional-grade USB-to-serial solution, known for its stability on Windows 10 64-bit compared to cheaper consumer alternatives. While it is now considered a legacy product, official driver support remains available. Performance Review & Compatibility
Reliability: Reviewers highlight that Edgeport drivers are robust enough for mission-critical industrial systems, offering better flow control and buffering than standard Prolific or FTDI-based chips.
Persistent COM Ports: A major advantage of these drivers is the ability to lock a specific COM port number to the device, even if you plug it into a different USB port on the same PC.
Windows 10 Support: Official drivers (v6.05 and newer) fully support Windows 10 64-bit. Users report successful operation even on systems that struggle with older serial adapters. Driver Installation Guide (v6.05)
To ensure a clean setup on Windows 10, follow the official Digi installation procedure:
Do not plug in the device yet. Connecting it before the driver is installed can lead to "unrecognized device" errors.
Download and Run: Get the v6.05 driver from the Digi Support Hub. Right-click the .exe and select Run as Administrator.
Connect Device: Once the installation window disappears, plug the Edgeport/1 into your USB port. It should now enumerate correctly.
Verify: Open the Edgeport Configuration Utility (found under Digi USB in the Start Menu) to confirm the COM port assignment. Critical Troubleshooting
Legacy vs. Modern: If your device is an older "Legacy" model, ensure you are using the specific legacy driver package if v6.05 fails to recognize it.
TUSB3410 Error: If Windows identifies the device as a "TUSB3410" instead of an Edgeport, it often indicates a driver conflict or a hardware fault where the EEPROM is not being read.
USB 3.0 Compatibility: While mostly stable, some older versions of the driver had issues with USB 3.0 (blue) ports; ensure you are on v6.05 or higher to resolve these host controller conflicts.
How to install the Edgeport driver in Windows - Digi International
The Digi Edgeport/1 remains a robust solution for adding high-speed serial connectivity to modern systems via USB. While many legacy hardware components struggle with modern operating systems, the Edgeport/1
is fully compatible with Windows 10 64-bit using the latest drivers from Digi International. Essential Driver Information
To ensure stable operation on a 64-bit architecture, you must use the correct driver version. The most current and widely recommended version for Windows 10 is v6.05. Driver Version: 6.05 (latest)
Filename: 40002537_6.05_N.exe (or similar depending on the exact sub-version) Developer: Digi International Official Support Step-by-Step Installation Guide
Installing the Edgeport driver requires a specific sequence to avoid hardware recognition errors. 1. Preparation Disconnect the Device: Do NOT plug the Go to product viewer dialog for this item. into your USB port before the software is installed.
Administrator Rights: Ensure you are logged in with administrative privileges. 2. Installation Process
Download: Get the v6.05 driver from the Digi Edgeport Support Page.
Run Installer: Right-click the downloaded .exe file and select Run as Administrator. Setup:
Click the Setup button. A black command-line window will appear while the drivers are registered; wait for it to close automatically. Connect Hardware: Once the installer finishes, plug the Edgeport/1
into an available USB port. Windows will now automatically detect the device and assign a COM port. 3. Verification To confirm the installation was successful:
Open the Start Menu and navigate to the Digi USB program group. Launch the Edgeport Configuration Utility Edgeport/1
should appear under the General tab with its assigned COM port listed. Optimizing for Windows 10 64-bit digi edgeport 1 driver windows 10 64 bit
How to install the Edgeport driver in Windows | Digi International
Title: SOLVED: Digi Edgeport/1 Driver on Windows 10 64-bit (Official & Working Method)
Post:
I recently needed to get an old Digi Edgeport/1 (single-port USB to serial adapter) working on a fresh install of Windows 10 Pro 64-bit (version 22H2). Plug-and-play did NOT work automatically, and Windows Update couldn’t find a driver.
After some digging, I found the correct working driver. Here’s the fix:
The Problem:
The Solution – Use Digi’s “RealPort” Driver (Works for Edgeport/1):
Digi has consolidated their drivers. Do not use the old “Edgeport Driver” – use the RealPort Com Port Redirector package. It includes the correct .INF and signed 64-bit driver for all Edgeport models (Edgeport/1, /4, /8, etc.).
Steps that worked for me:
Install the driver BEFORE plugging in the device (recommended):
Reboot your PC (important for the driver signing to fully register).
Plug in your Digi Edgeport/1.
Troubleshooting if it still doesn’t work:
Result: My Edgeport/1 is now working perfectly on Windows 10 64-bit, passing serial data at 115200 baud with no dropped packets.
Avoid these dead ends:
Hope this saves someone the hours I lost! Reply if you need the exact version number or further help.
System: Windows 10 Pro 22H2 64-bit | Digi Edgeport/1 (P/N: 300-1000-01)
The latest official driver for the Digi Edgeport/1 on Windows 10 (64-bit) is version 6.05. While the Edgeport line is officially designated as "end of life" by Digi International, this driver package remains compatible with modern 64-bit Windows environments. Download and Installation Steps
Follow this specific sequence to ensure the driver installs correctly without hardware conflicts:
Disconnect the Device: Do NOT have the Edgeport plugged into your computer when you start the installation.
Download Driver: Obtain the official Digi Edgeport driver v6.05 (often listed as file 40002537_6.05_N.exe).
Run as Administrator: Right-click the downloaded .exe file and select Run as Administrator.
Complete the Setup: Click the Setup button. A black command window will appear during the process; wait for it to disappear completely.
Connect Hardware: Plug the Edgeport/1 into a USB port. Windows should now automatically detect the hardware and finish the final installation steps. Verification and Configuration
To confirm your device is working properly, use the built-in utility included with the driver:
Locate Utility: Go to Start > All Apps > Digi USB > Edgeport Configuration Utility. After the installation and system reboot, you need
Check Status: Your Edgeport/1 should appear under the General tab. Expanding the entry will show the assigned COM port.
Firmware: Connecting the device to a computer with this driver installed will automatically update its firmware if needed. Troubleshooting Tips
Driver Signing: If the installation fails due to security restrictions, you may need to temporarily disable driver signature enforcement in Windows settings.
COM Port Changes: Use the Edgeport Configuration Utility to manually reassign COM port numbers if they conflict with other hardware.
Do you need help reassigning specific COM port numbers for your serial application?
How to install the Edgeport driver in Windows - Digi International
For the Digi Edgeport/1 on Windows 10 (64-bit), the most reliable driver is version 6.05, which is officially supported for modern Windows environments. 📥 Official Download & Setup
While Digi has marked some Edgeport lines as legacy, drivers remain available through their Support Resources.
Download: Get the 40002537_N.exe (v6.05) package from the Digi Knowledge Base.
Permissions: You must have Administrator rights to run the installer. Sequence: Disconnect the Edgeport device first. Run the installer and wait for the command window to close.
Plug the device into a USB port to trigger automatic finalization. 🛠️ Key Configuration Utility
Once installed, Windows doesn't always show a shortcut immediately. You must have the device connected for the full utility to appear.
Location: Find the Edgeport Configuration Utility under the "Digi USB" folder in the Start Menu.
Direct File: On 64-bit systems, the executable is edgeport64.exe located in the \system32\ folder.
Verification: Open the utility to see your device under the "General" tab and confirm COM port assignments. 💡 Troubleshooting & Indicators Status Light: Blinking Red: Establishing communication or driver issue. Solid Green: Device is ready and operating normally. Amber: Active serial port data transfer.
Legacy Drivers: If v6.05 fails, older versions like v5.10 (revision G) are available for specific legacy hardware revisions, though v6.05 is generally backward compatible.
Firmware: The Edgeport firmware usually updates automatically when connected to a system with the latest drivers.
🌟 Pro Tip: If Windows 10 fails to recognize the device, manually right-click the installer and select "Run as Administrator" to ensure all registry keys are created properly.
If you tell me what specific error you're seeing (e.g., Code 10, "Device not recognized") or the hardware part number, I can give you more targeted help.
How to install the Edgeport driver in Windows - Digi International
Here’s a clear, helpful post you can use on a forum, blog, or internal IT knowledge base.
Title: SOLVED: Digi Edgeport/1 Driver for Windows 10 64-bit
Post:
If you need to get a Digi Edgeport/1 (or Edgeport/2, Edgeport/4, etc.) working on Windows 10 64-bit, here’s what actually works as of 2025–2026.
Official working driver:
Digi’s Edgeport Driver v8.0.2 (or newer) includes native Windows 10 64-bit support.
Direct steps:
Plug in the Edgeport/1
Troubleshooting if it doesn’t work:
Still on an old driver?
Do not use Windows Update’s generic driver. Digi’s v8.0.2 is the stable, signed version for Win10 64-bit.
Let me know if you have an Edgeport/1, /2, /4, or /8 – same driver works for all.
Digi Edgeport/1 is a high-performance USB-to-serial converter that provides instant COM port expansion for Windows 10 (64-bit) systems
. This "bump-in-the-cable" solution is frequently used in mission-critical enterprise environments like retail stations and emergency vehicles. Digi International Driver Installation for Windows 10 (64-bit)
The current supported driver version for modern Windows operating systems is Digi International Preparation device into your computer before starting the installation : Obtain the Windows driver package from the Digi Edgeport Support Page : Right-click the downloaded executable (e.g., 40002537_6.05_N.exe ) and select Run as Administrator : Click the
button. A black command window will briefly appear as drivers are loaded. Connection : Once the installation window disappears, plug the Edgeport/1
into a USB port. Windows will automatically finish the device installation Digi International Verifying Successful Installation After connecting the device, use the Edgeport Configuration Utility to ensure it is working correctly: Locate Utility Edgeport Configuration Utility Confirm Connection : The device should appear under the
tab. Double-clicking the entry will list the assigned serial (COM) ports. LED Status
: In normal idle operation, the System Status LED on the device should blink slow green Digi International Troubleshooting and Legacy Support Permissions
: Administrative rights are required for a successful installation. Direct Connection : For best results, connect the
directly to the computer's USB port rather than through a non-powered hub or extension cable Legacy Drivers
: If you have an older "Legacy" Edgeport model, you may need specific older driver versions (like v5.70), which are still available as a courtesy on the Digi Knowledge Base has been assigned to your Edgeport/1 in Device Manager?
How to install the Edgeport driver in Windows - Digi International
To install the Digi Edgeport/1 Windows 10 64-bit , you should use the latest driver package (typically version 6.x) available from the official Digi Support Resources Digi International Installation Steps : Obtain the latest Windows driver from the Digi International support page Pre-Installation
: Disconnect the Edgeport/1 from your PC before starting the installation. Run Installer : Execute the downloaded file (e.g., a self-extracting ). It typically extracts files to C:\edgeport drivers and launches a command-prompt setup. Connect Device
: Plug the Edgeport/1 into a USB port after the driver installation is complete. Windows should then automatically detect the device and assign COM ports. : Open the Edgeport Configuration Utility
(located in the "Digi USB" program group) to confirm the device is listed and serial ports are active. Digi International Key Specifications & Troubleshooting Digi Edgeport USB-to-Serial Converters Support Resources
Contact Information. 1-877-912-3444 952-912-3444 Contact Digi sales. Digi International
How to install the Edgeport driver in Windows - Digi International
Using Digi’s RealPort or PortVision DX tool (downloadable from Digi's website), you can:
Crucial Warning: Avoid third-party "driver updater" websites. They often bundle malware or supply generic drivers that will BSOD (Blue Screen of Death) your Windows 10 64-bit system.
The Digi EdgePort 1 is a single-port serial device server/adapter that requires a vendor driver to create a virtual COM port on Windows. For Windows 10 64-bit, follow this concise guidance to get it working and stable.
When you plug a Digi Edgeport 1 into a Windows 10 64-bit PC for the first time, you might experience one of three scenarios:
The root cause? Starting with Windows 10 version 1607 (Anniversary Update), Microsoft requires all kernel-mode drivers to be digitally signed by Microsoft’s Hardware Dev Center. Older Edgeport drivers from 2012 or earlier do not have this signature. If you see this entry without a yellow