Samsung M2020w Free | Firmware Reset
We just reset the settings (NVRAM). This does not downgrade your firmware version. If you have a corrupt firmware file (the operating system of the printer), this button reset won't fix it. But for 99% of M2020W "I forgot my password" or "Wi-Fi won't connect" problems? This works like magic.
Have a different error? Drop a comment below with the code showing on your screen.
Disclaimer: This is a user-supported guide. Always refer to your manual. Resetting your device will delete saved networks.
Liked this post? Pin it to your printer board so you can find it next time your M2020W acts up.
Samsung M2020W , you can perform a free factory reset to clear system errors using physical button combinations. However, if your goal is to bypass "Toner Empty" messages to use refilled or non-original cartridges, this typically requires a permanent firmware fix Free Factory & Maintenance Reset
This standard reset clears the printer's memory and is often used to fix connectivity or minor hardware glitches. Simple Reset : Turn the printer on, hold the Stop/Cancel button (just above the Power button) for 10–15 seconds until the LEDs flash, then release and restart the device. Hardware Initialization Turn the printer off. Press and hold the Stop/Cancel button while plugging in the power cord. Continue holding for 10 seconds , then release. Immediately press and hold both the Stop/Cancel buttons for another 25 seconds until the printer cycles through its startup routine. Permanent Firmware "Fix" (Chipless Firmware)
A permanent firmware reset allows the printer to function without the toner chip, meaning the counter will always show . While some official firmware updates are free via HP/Samsung Support , "chipless" fixes are often paid third-party services. Common Steps for Installing a Firmware Fix: Samsung M2020W firmware update on MacOS 6 Sept 2018 —
Finding a "free" firmware fix for the Samsung Xpress M2020W is difficult because these "Fix" files are usually unique to a printer's specific Serial Number and CRUM (chip) number. Using a generic file from the internet can "brick" (permanently disable) your printer.
If you are looking for a paper guide or instructions on how to reset the printer or update it safely, here are the official and common manual methods. 1. Hard Reset (No Software Needed)
This is a standard "soft" reset to clear temporary errors or memory: firmware reset samsung m2020w free
Method A: Turn the printer on. Hold the Stop/Cancel button for 10–15 seconds until the LEDs flash, then release and restart the device.
Method B (Network/Wi-Fi Reset): Hold the WPS button for 5 seconds until the LED blinks to reset network and Wi-Fi settings. 2. Official Firmware Update (Safe & Free)
If your printer is acting up (e.g., paper jams, print quality), you can download the official firmware for free from HP Support (who now owns Samsung's printer division). Download: Visit the Samsung Xpress M2020W Support Page. Process: Connect the printer via USB. Download the firmware file (e.g., M2020W_V3.00.01.23.hd).
Drag and drop the .hd file onto the usblist2.exe (or usbprns2.exe) program provided in the download.
Wait 1–2 minutes until the printer reboots itself. Do not turn it off during this time. 3. "Fix" Firmware (Bypassing Toner Chips)
Third-party sites often sell custom firmware to let you use refilled cartridges without a chip. To even consider this, you must first print a Configuration Report to get your printer's specific data:
Print Configuration Report: Hold the Print Screen/WPS button for 10 seconds until the LED flashes once.
Print Supplies Information: Hold the Print Screen/WPS button for 15 seconds until the LED stays green. Official Update "Fix" Firmware (Reset) Cost Free Usually Paid ($5–$20) Purpose Fixes bugs/errors Bypasses toner chip limits Risk High (May void warranty) Source HP Support Third-party (e.g., eReset, ORPYS)
Important Note: Using a "free" file found on a forum that wasn't built for your specific Serial Number will likely break your printer. We just reset the settings (NVRAM)
Are you trying to fix a specific error code, or are you trying to use a refilled toner cartridge without buying a new chip? Samsung M2020 | M2020W Firmware FIX
To perform a firmware reset on a Samsung Xpress M2020W for free, you can use a specific button combination on the device to restore factory settings or reset network configurations. While professional "fix firmware" files exist to bypass toner chip limits permanently, they often require a fee; however, standard troubleshooting resets can be done at no cost. Free Methods for Samsung M2020W Reset
Depending on whether you need to fix a connectivity issue or a general system error, choose from the following free manual methods:
Factory Settings Reset: Turn on the printer and hold the Stop/Cancel button for approximately 10–15 seconds. Release the button once the LEDs start flashing, then restart the device to complete the reset.
Network (Wi-Fi) Reset: If you've lost your Wi-Fi password or the printer won't connect, hold the WPS button (located above the power button) for 5 seconds until the LED blinks.
Print Configuration Report: To check your current firmware version and serial number, hold the Print Screen / WPS button for about 10 seconds until the LED flashes once. Advanced "Firmware Fix" (Chipless Reset)
Many users search for a "firmware reset" specifically to use refilled toner cartridges without replacing the MLT-D111 toner chip. This process involves installing a modified firmware file (.hd) to make the printer "chipless."
Permanent Fix: A successful firmware fix allows the printer to show 100% toner levels indefinitely and avoids "Toner Not Recognized" errors.
Installation Process: The fix typically involves connecting the printer via USB and dragging the firmware file onto a tool like usblist2.exe. Disclaimer: This is a user-supported guide
A Note on "Free" Files: While some forums offer free "fix" files for older firmware versions like V3.00.01.23, many reliable generators now charge a small fee ($13–$16) because the files must be customized to your specific Machine Serial Number and CRUM code. Using a generic "free" file not matched to your serial number can permanently damage (brick) your printer. Troubleshooting Common Errors
If a reset doesn't solve your problem, the issue might be hardware-related rather than firmware-based:
Samsung Printer Reset & Error Code Guides - Farbtoner.com GmbH
Reset: Turn on the device → Menu → System → Factory Settings. Alternatively, hold the Stop button for 15 seconds. Farbtoner.com GmbH Samsung Xpress SL M2020 M2023 M2024 M2026 M2027 M2029
Here are a few options for the text, depending on where you intend to use it (e.g., a website, a forum post, or a YouTube description).
Do not attempt to downgrade the firmware via USB. HP/Samsung blocked older firmware versions, and a failed downgrade will permanently brick the printer (no recovery mode exists for the M2020W). The reset above is the only safe, free method.
Here’s a draft for a blog post titled “How to Perform a Firmware Reset on a Samsung Xpress M2020W (Free & Easy)” — written in a helpful, clear, and search-friendly style.
A: No. The Cancel+Start sequence is an official, documented factory routine in the firmware. It is not a hack or exploit. Samsung intended this for service technicians to use without charge.