Hager Controls Bp 10140 Manual May 2026

| Problem | Likely Fix | |--------|-------------| | No power | Check fuse, 24V supply, terminal polarity | | Input not reading | Jumper test – short input to common; LED should blink | | Output not switching | Overload? Measure output voltage. Check program logic. | | Can’t connect to PC | Baud rate (9600/19200), COM port, cable type (straight vs cross) |

The Hager Controls BP 10140 manual is your roadmap to mastering this robust industrial timer. Whether you need to wire it into a new heating system or troubleshoot a lighting circuit that refuses to turn off, the manual provides the authoritative answers.

Action Steps:

By respecting the guidelines laid out in the manual, you ensure safety, extend the lifespan of your device, and maintain precise control over your electrical loads. If you cannot locate the original document, treat this guide as a starting point—but always verify terminal labels and voltages with a qualified electrician before handling live equipment.

Disclaimer: This article is for informational purposes only. Always refer to the official Hager documentation provided with your specific product revision. Electrical work carries risk of injury or death; consult a licensed professional.

The Hager BP 10140 is a digital time switch, often associated with or listed under the model number Go to product viewer dialog for this item.

. While "BP 10140" refers to the postal address of Hager Controls S.A.S. in France (Boîte Postale 10140), it is frequently found on the device's labeling. Key Features & Operations

The following features are typical for digital time switches in this series, such as the Hager EGN103

Official Manuals: You can find technical documentation and user instructions on the Hager Download Center.

Video Guide: For visual learners, there are short tutorials on setting up similar 24-hour Hager timers on YouTube. Downloads - Hager

The designation BP 10140 is not a product model number; rather, it refers to the postal box address for Hager Controls S.A.S. (B.P. 10140, 67703 Saverne Cedex, France) found on many of their technical documents. Because this address appears on a wide range of devices—from time switches and KNX controllers to server interfaces—finding the "manual" requires identifying the specific device you have. Identifying Your Device hager controls bp 10140 manual

To find the correct manual, look for a specific part number on the front or side of the unit. Common Hager product codes often follow formats like: EHN010 / EHN011: Daily/Weekly analog time switches. EG103: Digital time switches. TJA470 / TJA670: domovea servers. TXM6XX / TYM6XX: KNX output modules. General Operating Guide for Hager Time Switches

If your device is a standard timer (one of the most common products bearing the BP 10140 address), here is how to use it based on standard Hager documentation: 1. Wiring and Installation

Connection: Typically, the neutral wire connects directly to the load. The line wire connects to the timer, with a loop feeding terminal 1.

Load: The load itself is connected to terminal 2, ensuring the circuit passes through the timer's relay.

Safety: All electrical work must be performed by a qualified electrician. Ensure the circuit is protected by a 10A breaker. 2. Setting the Timer

Adjusting Time: Rotate the main dial until the current hour aligns with the arrow indicator. Programming Intervals:

Analog Models: Use the small "pins" or tabs around the dial. Pushing tabs in (or towards one side) typically sets the "ON" state, while leaving them out (or towards the other side) is "OFF".

Intervals: Each tab usually represents 15 minutes or 1 hour depending on the model.

Operating Modes: Most units feature a three-position switch:

Clock Icon: Automatic mode (follows your programmed schedule). 1 (or "I"): Permanent ON (manual override). 0: Permanent OFF. 3. Maintenance and Troubleshooting

Battery Backup: Some models like the Hager EHN011 include a power reserve battery. If the power fails, the timer continues to run.

Resetting: If the unit becomes unresponsive, digital models often have a reset button accessible via a small pinhole; analog models may simply need the time re-aligned after a total power loss if they lack a battery.

Manual Override: Use the built-in buttons or toggles to cycle through manual states for fault finding or temporary changes. Official Documentation Links Downloads - Hager

The Hager BP 10140 (located at 33 rue Saint-Nicolas, B.P. 10140, 67703 SAVERNE CEDEX, France) is a manufacturer address frequently listed on various Hager modular devices, including analogue and digital time switches/controllers

. Based on similar Hager daily time switches, the manual covers installation, setting, and operation of 24-hour DIN-rail timers. Hager Time Switch Overview

The device controls electrical loads based on a 24-hour schedule, often used for lighting, heating, or industrial processes. Operating Modes:

The switch usually has three positions: Manual ON, Automatic (watch symbol), and Manual OFF. Interface:

Features a rotating dial with segments (pins) representing 15-minute intervals, with a clock face for setting the current time. Installation & Wiring Installation: | Problem | Likely Fix | |--------|-------------| |

Must be performed by a qualified electrician, ensuring compliance with local standards.

Connect the neutral directly to the load and the line wire through terminal 1, with the load output on terminal 2 (standard configuration). Device Type: Designed for 230 V~, 50–60 Hz operation. Setting the Schedule & Time Set Current Time:

Rotate the outer dial until the current time aligns with the indicator arrow. Program Schedule (Pins):

Push the pins towards the center (or to the "1" side) to turn the load ON. OFF State:

Push the pins towards the outside (or to the "0" side) to turn the load OFF.

To have lights on from 7 PM to 6 AM, push all segments within that range to the ON position. Operating Instructions & Troubleshooting Mode Switch:

Ensure the mode selector is set to the Automatic (Watch Symbol) position for the timer to run. Power Failure:

If the timer loses power, it will not track time and will need to be readjusted. Battery Backup:

Some models have a backup battery (e.g., CR2032) to retain time and programs, which should be replaced if needed.

Disclaimer: As "BP 10140" refers to the manufacturer address rather than a specific product model number, these instructions are based on common Hager time switches (e.g., EHN010, EHN011, EHN110) associated with that documentation location. Please check the actual label on the side of your device for a more specific model number (e.g., EHN010, EH110, or a 7-digit code) for the exact manual.

hager timer connection and setting full information #zkmultitech

Hager BP 10140 is not a specific device model but rather the postal box address for Hager Controls S.A.S.

(B.P. 10140, 67703 Saverne Cedex, France) printed on various product manuals. However, this address is most frequently associated with the Hager EG103

digital time switch in second-hand markets and technical documentation. device.report Device Report: Hager EG103 Digital Time Switch

This report covers the digital time switch often identified by the Hager Controls address "BP 10140." 1. Key Features & Functions Single Channel Programming : Supports 24-hour and 7-day scheduling. Operating Modes

: Features automatic mode, continuous ON, and continuous OFF. Memory & Backup

: Retains programmed data even during power outages via an internal battery; however, date and time may be lost if the battery is changed without mains voltage. User Interface

: Includes a digital LCD display showing the current time, date, and automatic status. 2. Installation Guidelines : Designed for standard 35 mm DIN rail Connect the wire directly to the load (e.g., light). Connect the wire to the timer's line terminal. Connect the By respecting the guidelines laid out in the

to terminal 2, ensuring the line to the load passes through the timer.

: Must be installed by a qualified electrician in accordance with national safety standards. device.report 3. Programming Instructions Accessing Menu : Press the button to exit automatic mode and enter the programming ( ) interface. Setting Days

: Select individual days (1=Monday to 7=Sunday) or groups (weekdays/weekends) using the buttons and confirming with Setting Times

: Program the "ON" time first, followed by the "OFF" time. Confirm each hour and minute selection with Verification

: Use the "Viewing Mode" (indicated by an eye symbol) to scroll through and verify programmed events. 4. Technical Support & Manuals

Detailed technical documentation and specific device manuals can be found on the Hager Support Downloads page or via the Hager India Technical Catalogue Ed 10140 - device.report

The Hager BP 10140 (EG103 series) is a single-channel, DIN-rail mounted digital time switch featuring 24-hour or 7-day programming with up to 56 steps. It allows for manual overrides, includes a power reserve for memory retention, and requires professional installation. Detailed programming, including setting ON/OFF times and activating automatic mode, is accomplished via front-face buttons. For a video walkthrough of the programming process, visit Hager EG103 Programming

The Hager BP 10140 is not a specific model number, but rather a reference to the manufacturer's postal address (B.P. 10140) located in Saverne, France. This address appears on various Hager device manuals, including timers like the EG103, EHN011, and the B.IQ push button display.

If you are looking for a manual for a specific Hager control device found with this address, common models include the EG103 Digital Time Switch and the EHN010/011 Analog Timers. 1. Hager EG103 Digital Time Switch Manual The EG103 is a 1-channel weekly digital timer.

Time and Day Setting: Use the + or - keys to scroll through minutes, hours, and days. Programming: Press menu, select prog, and press ok. Select the day or group of days (1 = Monday, 7 = Sunday). Choose the state (On or Off).

Enter the switching hour and minutes, confirming each with ok.

Resetting: To clear all programs and time, press and hold +, -, ok, and menu simultaneously. 2. Hager EHN010 / EHN011 Analog Timer Manual

These are daily cycle time switches typically mounted on a DIN rail. Ed 10140 - device.report

Based on crowd-sourced data from electricians who have used the Hager BP 10140, here are real-world issues:

In the realm of modern building automation and electrical installation, Hager stands as a prominent figure, known for producing reliable and innovative solutions. Among their extensive portfolio of control systems, the Hager Controls BP 10140 is a component that frequently arises in discussions regarding energy management and lighting control.

Whether you are an electrician tasked with an installation, a facility manager maintaining a system, or a DIY enthusiast trying to understand your home automation setup, accessing and understanding the manual for the BP 10140 is crucial. This article provides a comprehensive overview of the device, its applications, and a summary of the critical information typically found within its technical manual.

A: You likely have conflicting programs. Enter programming mode and review "Program 1" through "Program 8." Delete unnecessary programs. The manual suggests using the "Erase All" function to start fresh.

The BP 10140 may involve complex internal connections. One wrong terminal can create a short circuit, damage downstream electronics, or cause a fire. The manual includes terminal identification, busbar compatibility, and torque specifications for screws.