Suzuki K6a Engine Ecu Pinout High Quality May 2026

| Pin | Signal Name | I/O | Type | Notes | |-----|---------------------------|------|---------------|--------------------------------| | A1 | Injector #1 | Out | Low-side drive| 12V when off, pulsed ground | | A2 | Injector #2 | Out | Low-side drive| | | A3 | Injector #3 | Out | Low-side drive| | | A4 | Fuel pump relay | Out | Ground switch | On during cranking/running | | A5 | Tachometer output | Out | 0-12V square | 4 pulses per engine revolution | | A6 | MIL (Check Engine Light) | Out | Ground switch | Active low | | A7 | Cooling fan relay 1 | Out | Ground switch | Low speed | | A8 | Cooling fan relay 2 | Out | Ground switch | High speed | | A9 | EGR solenoid (if equipped)| Out | PWM ground | Not on all markets | | A10 | A/C compressor relay | Out | Ground switch | | | A11 | VVT oil control valve | Out | PWM (80-200Hz)| On K6A with VVT (late models) | | A12 | Idle Air Control (IAC) – | Out | PWM stepper | 4-wire stepper motor | | A13 | IAC Coil 2 | Out | | | | A14 | IAC Coil 3 | Out | | | | A15 | IAC Coil 4 | Out | | | | A16 | +12V Battery (constant) | Power| | From EFI main relay | | A17 | Injector common +12V | Power| | From fuel pump relay | | A18 | Ignition coil #1 – trigger| Out | 5V logic | To igniter (if external) | | A19 | Ignition coil #2 – trigger| Out | 5V logic | | | A20 | Ignition coil #3 – trigger| Out | 5V logic | | | A21 | Wastegate solenoid (turbo)| Out | PWM ground | Max 10Hz (boost control) | | A22 | Purge control solenoid | Out | PWM ground | Evaporative emissions | | A23 | Sensor ground | GND | Analog return| 0V reference | | A24 | Power ground 1 | GND | High current | To engine block | | A25 | Power ground 2 | GND | High current | | | A26 | O2 sensor heater (front) | Out | PWM ground | Heated oxygen sensor | | A27 | O2 sensor heater (rear) | Out | PWM ground | If dual sensor | | A28 | MAF sensor +5V reference | Out | +5V | To MAF pin 3 | | A29 | TPS +5V reference | Out | +5V | Throttle position sensor | | A30 | Cam position signal (CMP) | In | Hall effect | 0-5V digital | | A31 | Crank position (CKP) + | In | Magnetic | High resolution | | A32 | Crank position (CKP) – | In | Magnetic | |

A high-quality pinout allows you to strip the unnecessary chassis wiring. You only need: suzuki k6a engine ecu pinout high quality

Then connect your gauges: tach (B10), temp (A19), and check engine (A12). | Pin | Signal Name | I/O |

Plug A (18 pins) – Row 1 pins 1–9, Row 2 pins 10–18 A high-quality pinout allows you to strip the

Pin 1 (top left) → A-1 (B/ground), A-2 (B/Y), A-3 (R), etc.

Plug B (18 pins) – similar layout.

Plug C (34 pins) – two rows of 17. Pin C-1 top left, C-18 bottom left. C-19 top right, C-34 bottom right.