Many TX9 Pro units were sold by OEMs like "VONTAR" or "H96". Check the manufacturer’s support page:
This is the most common variant.
The single biggest mistake users make is downloading the first "TX9 Pro firmware" they find. There are multiple hardware variants of the TX9 Pro. Using the wrong firmware will permanently brick your device.
Do not download anything until you complete this step. You must open the plastic case of your TX9 Pro (the warranty is already void if you are here).
How to open it: Use a plastic guitar pick or a thin knife to pry open the seam between the top acrylic panel and the plastic bottom.
Once open, look for the following identifiers:
There is no direct manufacturer website for TX9 Pro (sold under many brands: VONTAR, H96, TANIX, etc.). However, official stock firmware is distributed via:
| Issue | Likely Cause | Solution |
|-------|--------------|----------|
| Wi-Fi won’t turn on | Wrong Wi-Fi driver in firmware | Reflash correct version matching Wi-Fi chip |
| Boot loop after flash | PCB version mismatch | Use USB Burning Tool with “Erase flash” and “Erase bootloader” checked |
| Device not detected by PC | No driver installed | Install libusb driver via Zadig or WorldCup Driver |
| Remote control not working | Different IR protocol | Copy remote.conf from old firmware to new one (via ADB) |
Since no single manufacturer supports the TX9 Pro, your only lifeline is the enthusiast community. To recap:
If you successfully revive your TX9 Pro, consider uploading your working firmware file to the Internet Archive so the next person searching for a "tx9 pro android tv box firmware link" doesn't have to struggle as much as you did. tx9 pro android tv box firmware link
Have a working link that expired? Share it in the comments below (no .exe files, only .img archives).
Updating your TX9 Pro Android TV box Go to product viewer dialog for this item.
can be done through official firmware files or third-party repositories. Below is a guide on how to locate the firmware and perform the installation. 1. Official & Recommended Firmware Links While several manufacturers use the " Go to product viewer dialog for this item.
" name, the most common versions are associated with Tanix or Tenda.
Tanix Official Support: You can find product-specific files at the Tanix Firmware Centre. Tenda Official Downloads: If your device is the Tenda TX9 Pro Go to product viewer dialog for this item.
model, the latest official firmware (version V22.03.02.09 or newer) is available on the Tenda Global Support Page.
Alternative OTA Package: A legacy OTA zip file is also hosted on SourceForge for older hardware versions. 2. Update Methods
There are two main ways to install the firmware depending on the file type you downloaded. Method A: USB / SD Card (For .zip OTA files) This is the easiest method and does not require a computer. Prepare Media: Format a USB drive or SD card to FAT32. Copy File:
Place the update.zip firmware file into the root directory (not inside any folders). Insert & Update: Plug the media into your Many TX9 Pro units were sold by OEMs like "VONTAR" or "H96"
. Go to Settings > Device Preferences > About > System Update and select Local Update.
Wait: The device will reboot and install. Do not power off during this process. Method B: USB Burning Tool (For .img files)
Use this if your device is "bricked" or you have a full image file. How to Update Android TV Box Firmware Manually
The TX9 Pro Android TV box typically runs on a Tanix-based system. Depending on your specific hardware version (CPU and board ID), firmware links and installation methods vary. Official & Verified Firmware Links
Tanix Official Centre: The Tanix TV Box Firmware Centre provides official system files for their product lineup.
Tenda TX9 Pro (V22.03.02.09): Specific firmware versions (like v22.03.02.09) for certain TX9 Pro variants are hosted on Internet Archive.
Legacy Android 7.1.2: For older S912 SoC models with 3GB RAM, firmware images are available through community sites like AndroidPC.es. Essential Pre-Installation Checklist
Before downloading, you must identify your device's internal specs to avoid "bricking" (permanently disabling) it:
Identify the SoC: Most TX9 Pro boxes use the Amlogic S912 or Allwinner H616. Since no single manufacturer supports the TX9 Pro,
Check the Board ID: Open the device or check the system settings to find the exact board number (e.g., H616-V3.0).
Verify the Version: Some firmware is strictly for V1.0 hardware and requires a minimum existing version (e.g., V22.03.02.XX) to install. How to Update Your Firmware Over-the-Air (OTA):
Go to Settings > Device Preferences (or About) > System Update. Click Check for Updates while connected to Wi-Fi. Manual USB Flashing: Download the .bin, .img, or .trx firmware file.
For Amlogic chips, use the Amlogic USB Burning Tool on a PC.
Put the device into Recovery Mode by holding the reset button (usually hidden inside the AV port) while plugging in the power. Import the firmware into the burning tool and click Start.
Warning: Do not power off the device during the upgrade process, as this can cause unrecoverable system failure.
Since "TX9 Pro" is a generic brand name used by many manufacturers in China, there isn’t one single official website for these devices. This makes finding the correct firmware a mixed bag of frustration and necessity.
Here is a review of the process and the typical results when searching for "TX9 Pro Android TV box firmware links."
Follow this sequence exactly. Do not skip the driver installation.
Phase A: Install Drivers
Phase B: Connect & Flash