C&C includes roof panels, wall studs, windows, and curtain walls. Pressures are higher and more localized.
p = qh × G × Cp – qi × G × Cpi (Equation 6-20)
But here Cp is from Figure 6-11 through 6-17 (based on Effective Wind Area).
Key difference: Effective wind area = span × (span/3) but not less than span × width tributary. Smaller areas = higher Cp.
Example for roof zone (low-slope, Exposure C, qh = 30 psf):
Thus C&C pressures are often the governing load for cladding design.
[ p = q_z G C_p - q_h (GC_pi) ] [ p = 21.9 \times 0.85 \times 0.8 - 21.9 \times (0.18) = 14.89 - 3.94 = 10.95 \text psf (inward) ]
Similarly, leeward wall:
[
p = 21.9 \times 0.85 \times (-0.35) - 21.9 \times (0.18) = -6.52 - 3.94 = -10.46 \text psf (suction)
]
The MWFRS must be designed for combined action of windward positive and leeward negative.
Introduction
Wind load calculation is one of the most critical aspects of structural engineering. Unlike gravity loads, which are primarily static and predictable, wind loads are dynamic, stochastic, and highly sensitive to the geometry and location of a structure. In the United States, the standard governing these calculations is the American Society of Civil Engineers’ ASCE 7: Minimum Design Loads for Buildings and Other Structures.
Specifically, ASCE 7-05 represents a pivotal edition in the standard’s history. While later editions (such as 7-10 and 7-16) introduced significant changes by converting wind speeds to "ultimate" strength levels, ASCE 7-05 maintains the "allowable stress design" (ASD) approach to wind speeds. Understanding this standard is essential for engineers working on existing buildings or in jurisdictions that have not yet adopted newer codes. This essay outlines the fundamental methodology, key parameters, and procedural steps for calculating wind loads using ASCE 7-05.
The Analytical Procedure: Chapter 6
ASCE 7-05 outlines three methods for determining wind loads in Chapter 6:
Most structural engineers utilize the Analytical Procedure (Method 2). This method breaks the calculation down into distinct components: Velocity Pressure, External Pressure, and Internal Pressure.
Step 1: Determining Basic Wind Speed ($V$)
The foundation of the calculation is the Basic Wind Speed ($V$), defined as the 3-second gust speed at 33 feet (10 meters) above the ground in open terrain (Exposure C). In ASCE 7-05, these speeds are presented as "nominal" speeds (e.g., 90 mph, 100 mph) intended for use with Allowable Stress Design.
It is vital to note the distinction from later codes: ASCE 7-05 wind speeds are lower than the "ultimate" wind speeds found in ASCE 7-10 because they incorporate safety factors differently. The engineer must consult the wind speed maps provided in the standard, accounting for special wind regions and hurricane-prone coastlines.
Step 2: Velocity Pressure ($q_z$)
Wind speed is not static with height; it increases as one moves higher above the ground due to reduced surface friction. To translate wind speed into pressure, ASCE 7-05 uses the Velocity Pressure equation:
$$q_z = 0.00256 K_z K_zt K_d V^2 I$$
Where:
Step 3: Design Wind Pressure ($p$)
Once the velocity pressure is established, the engineer calculates the design pressures acting on the building surfaces. For rigid buildings (the vast majority of standard construction), the equation is:
$$p = q G C_p - q_i (GC_pi)$$
This equation represents the interaction of three distinct pressures:
Internal Pressure ($q_i (GC_pi)$):
Enclosure Classification and the Importance of Openings wind load calculation as per asce 7-05
A unique and critical aspect of ASCE 7-05 is the rigorous classification of building enclosures. The standard distinguishes between Enclosed, Partially Enclosed, and Open.
The Partially Enclosed classification is particularly important. If a building has a dominant opening (like a garage door or breached window) on the windward side, it can become partially enclosed. This creates a "ballooning" effect where internal pressure combines with external suction on the leeward wall, drastically increasing the net load on the structure. Engineers must consider scenarios where windows might break during a storm, potentially changing the building's classification during a wind event.
Uplift and Main Wind Force Resisting Systems (MWFRS)
ASCE 7-05 separates calculations into two distinct categories:
Conclusion
Calculating wind loads per ASCE 7-05 is a systematic process that requires careful attention to the specific definitions of exposure, enclosure, and pressure coefficients. While the mathematical formulas are straightforward, the engineer’s judgment in classifying the building and terrain is paramount.
Though newer standards have moved towards ultimate wind speed maps and Load Resistance Factor Design (LRFD) methodologies, ASCE 7-05 remains a widely referenced standard. Its Allowable Stress Design approach allows engineers to apply wind loads directly to allowable stress checks, simplifying the workflow for many practitioners. By mastering the balance of external coefficients and internal pressure effects outlined in ASCE 7-05, engineers ensure that structures are neither dangerously under-designed nor inefficiently over-built.
Note: ASCE 7-05 is a legacy standard (superseded by 7-10, 7-16, 7-22). Use it only if required by a specific existing project or building code. For new designs, use the current edition.